
What a Lumen Rating Tells You
A lumen is a unit of light output. As ProjectorCentral points out, it technically measures illuminance rather than how bright a picture looks to your eye, but it is the number every projector maker quotes. The trouble is that more than one way of measuring it is in use, so two projectors that both say "3,000 lumens" may not be directly comparable.
How ANSI Lumens Are Measured
ANSI lumens come from a published test procedure. The projector shows a fully white image, and a light meter takes readings at nine points arranged like a noughts-and-crosses grid. The nine readings are averaged, and the average is multiplied by the image area in square metres. The projector should be the only light source in the room, and reflective surfaces are kept to a minimum.
Because the result is an average across the whole picture, it describes the image as a whole rather than the brightest spot. The centre of a projected image is usually brighter than the edges, so an average is a more honest figure than a single reading.
Other Brightness Figures You Will See
- Centre-spot or peak lumens – These measure only the middle of the image, so they are almost always higher than the ANSI figure.
- Brightest-mode lumens – Spec sheets often quote the brightest picture mode, which can trade away colour accuracy. ProjectorCentral's reviews report separate figures for each picture mode and for eco mode.
- LED lumens – Some makers of LED and laser projectors rate perceived brightness rather than measured output. BenQ's own guide to the difference says its LED figures can run around 2.4 times the ANSI number, so a label that just says "lumens" tells you little.
- ISO lumens – ISO 21118 uses the same nine-point method but averages across several units of a model, and its figures tend to run somewhat higher than ANSI.
The practical rule is simple: look for the word ANSI next to the number, and be cautious of an unlabelled figure that is much higher than similar models quote.
Colour Brightness Matters Too
White brightness is not the whole story. ProjectorCentral notes that 3LCD projectors generally show colour at about the same brightness as white, while DLP models can make colour content look dimmer than their white rating suggests. If a model lists a separate colour-brightness figure, it is worth reading.
How Much Brightness Does Your Room Need?
There is no single right number, because brightness has to be matched to the room and the picture size. A larger image spreads the same light over more area, so it looks dimmer, and a room with daylight or lamps on can wash out a dim picture. ProjectorCentral explains that lumens set the range of image sizes that will look good for a given level of room light: too large and the picture looks washed out, too small and it can be uncomfortably bright.
As a rough guide, LG's UK helpful-hints page suggests about 1,000 to 2,000 lumens for images up to 60 inches, 2,000 to 3,000 for images up to 100 inches, and 3,000 or more beyond that. Treat these as starting points for a room you can darken. If you want to watch with some light on, ProjectorCentral suggests pairing high light output with an ambient-light-rejecting screen.
Native Resolution Versus "4K Supported"
Resolution is the other number worth checking, and the wording on the box matters. A projector's native resolution is the number of physical pixels on its imaging chip. A listing that says "4K supported" or "4K input" may only mean the projector accepts a 4K signal, so check what the chip itself is.
There is also a middle route. As What Hi-Fi explains, native 4K projectors use chips that reproduce about 8.8 million pixels individually. Pixel-shifting projectors use a 1920 x 1080 chip and project two slightly offset images that overlap to build a 3840 x 2160 picture. Brands call this different things: JVC uses E-Shift, Epson uses 4K Enhancement, and BenQ and Optoma use XPR.
What Hi-Fi concludes that native 4K beats pixel shifting in almost all cases, yet it still calls pixel shifting a significant step up from 1080p. Sound & Vision reported that most people at a normal viewing distance would struggle to see the difference between pixel-shifted and native 4K on resolution alone.
A Short Checklist
- Look for ANSI lumens, and treat unlabelled or LED-only figures with caution.
- Match brightness to image size and how dark you can make the room.
- Check the native resolution of the chip, not just the highest signal the projector accepts.
- Ask whether a quoted figure is for the brightest mode or the mode you would actually use.
Once you know what you need, the next question is where the projector goes. Our guide to setting up a projector at home covers throw distance, screen size and keystone, and projector or TV for a small room helps you decide whether you want one at all.
We may earn a commission when you buy through links on our site. Learn more · How we rank products


